To check which voice IC is bad

「To check which voice IC is bad」の編集履歴(バックアップ)一覧はこちら

To check which voice IC is bad」(2006/01/24 (火) 13:03:33) の最新版変更点

追加された行は緑色になります。

削除された行は赤色になります。

To check which voice IC is bad, do this: 1. turn the synth on. 電源を入れる。 2. press "poly1" button. poly1 ボタンを押す。 3. press lowest key, then next to lowest, then next to next to lowest...etc. (include the black keys too!) the lowest key is voice 1, next is voice 2, the next is voice 3.....etc. When you press a key that sounds "funny", it is associated with the bad voice. (you only have to press the 6 lowest keys) 一番低いキーを押す。次に低いキーを押す。・・・(黒鍵もね) 一番低いキーから順に voice1、2、3である。 押したときにオカシナ音がしたら、壊れたvoiceと結びつく。 (低い方の6つだけを押せば良い) 4. to double check, repeat steps 2 and 3 above. もう一度チェックするので、上のステップ2と3を繰り返す。 note: you may wish to manually dial up sounds with only the square wave, or only the saw wave, or only the sub Osc wave to verify which IC's have problems. Sometimes only one waveform will fail on a voice IC. Be sure to rule out the possibility of a failed filter IC too! Also don't be surprised if you find problems on both voices 1&2 or 3&4 or 5&6.... the reason being: there are only 3 voice IC's in a Juno-106 (two voices per IC) Sometimes the IC fails and takes out both voices. The voice IC is a SIM-like-mini-circuit with black epoxy coating over it. another note: The Voice IC SIM's go from right to left as you open the synth and look in: ___________________________________________ | / | \ | V6&5 V4&3 V2&1 / | F6 F5 F4 F3 F2 F1 \ ___________________________________________/ on each side of the Voice SIMs are similar filter SIM's (1 per voice). They are smaller. I have seen only 2 fail and about 12 voice IC's fail. Warning: Roland circuit boards after 1982 (such as those in the Juno-106) have plated through holes. This makes IC removal very tricky even with a good de-soldering workstation (The legs are held by solder on the top, bottom and inside of the hole). It is very easy to damage a solder pad or rip up a trace!!! If you are certain which voice IC is bad, carefully cut it from its legs then remove each leg individually (heat the leg on the solder side then pull the leg through from the component side using needle-nose pliers). One more thing... surrounding each Voice IC is a cluster of trimmer pots. It is here where you can adjust the filter resonance, cutoff freq., volume...etc. for each voice. It is possible (but unlikely) that someone could have turned the cutoff trimmer or VCA trimmer down on one voice. Thus causing apparent loss of a voice. I'll soon write a simple procedure where you can increase the cutoff and resonance of a 106 by just adjusting the trimmer pots and using your ears to balance all voices. (the most accurate way to calibrate certain parts of a synth in most circumstances) From your friendly lab tech Philip
To check which voice IC is bad, do this: どのVoice ICが壊れているかを確認する方法です。 しかし、テストモードで確認した方が確実だと思うので、簡易チェックであると考えます。 1. turn the synth on. 電源を入れる。 2. press "poly1" button. poly1 ボタンを押す。 3. press lowest key, then next to lowest, then next to next to lowest...etc. (include the black keys too!) the lowest key is voice 1, next is voice 2, the next is voice 3.....etc. When you press a key that sounds "funny", it is associated with the bad voice. (you only have to press the 6 lowest keys) 一番低いキーを押す。次に低いキーを押す。・・・(黒鍵もね) 一番低いキーから順に voice1、2、3である。 押したときにオカシナ音がしたら、壊れたvoiceと結びつく。 (低い方の6つだけを押せば良い) 4. to double check, repeat steps 2 and 3 above. もう一度チェックするので、上のステップ2と3を繰り返す。 note: you may wish to manually dial up sounds with only the square wave, or only the saw wave, or only the sub Osc wave to verify which IC's have problems. Sometimes only one waveform will fail on a voice IC. Be sure to rule out the possibility of a failed filter IC too! Also don't be surprised if you find problems on both voices 1&2 or 3&4 or 5&6.... the reason being: there are only 3 voice IC's in a Juno-106 (two voices per IC) Sometimes the IC fails and takes out both voices. The voice IC is a SIM-like-mini-circuit with black epoxy coating over it. another note: The Voice IC SIM's go from right to left as you open the synth and look in: ___________________________________________ | / | \ | V6&5 V4&3 V2&1 / | F6 F5 F4 F3 F2 F1 \ ___________________________________________/ on each side of the Voice SIMs are similar filter SIM's (1 per voice). They are smaller. I have seen only 2 fail and about 12 voice IC's fail. Warning: Roland circuit boards after 1982 (such as those in the Juno-106) have plated through holes. This makes IC removal very tricky even with a good de-soldering workstation (The legs are held by solder on the top, bottom and inside of the hole). It is very easy to damage a solder pad or rip up a trace!!! If you are certain which voice IC is bad, carefully cut it from its legs then remove each leg individually (heat the leg on the solder side then pull the leg through from the component side using needle-nose pliers). One more thing... surrounding each Voice IC is a cluster of trimmer pots. It is here where you can adjust the filter resonance, cutoff freq., volume...etc. for each voice. It is possible (but unlikely) that someone could have turned the cutoff trimmer or VCA trimmer down on one voice. Thus causing apparent loss of a voice. I'll soon write a simple procedure where you can increase the cutoff and resonance of a 106 by just adjusting the trimmer pots and using your ears to balance all voices. (the most accurate way to calibrate certain parts of a synth in most circumstances) From your friendly lab tech Philip

表示オプション

横に並べて表示:
変化行の前後のみ表示:
ツールボックス

下から選んでください:

新しいページを作成する
ヘルプ / FAQ もご覧ください。